Brick Paver Installation & Edging



Staging of product

A lot of paver projects will differ depending on access, site conditions, task size and obviously, the weather condition. These circumstances can have an overall effect on your task from a timing stand point. Cautious factor to consider ought to be required to figure out the time to start the paver installation. Constantly attempt to decrease or avoid any traffic on the ready areas.

The foreman or task supervisor ought to constantly have the materials (sand/ pavers) dispersed around the task site for simple and efficient installations. Paver pallets/bundles need to be put in a manner not to interfere with the paver installation. The correct pallet/bundle placement can make the actual task installation easier and quicker by reducing the total labor of dealing with the product.

Brick paver patterns

Pavers can be placed in various patterns depending upon their shape. Each paver shape will typically have numerous various hatch patterns that are provided by the producer.

Professionals require to take into factor to consider the traffic weight loads on their paver tasks. In most applications around the world, it has actually been shown that pavers laid in a herringbone pattern have carried out sufficiently.

Pavers that are 60 mm (2 - 3/8 in) density are suitable for pedestrian applications. Pavers that are going to be used in industrial or industrial applications must be 80 mm (3 - 1/8 in) in density.

Reference/starting point for brick paver installation

There are a number of conditions that identify the beginning point of a paver project.

When beginning to install pavers it is best to snap a true straight chalk line on the surface of the bedding sand or pull a real straight string line above the surface area of the bedding sand at the finished elevation of the pavers This will help as a guide for keeping straight joint lines and will also enable the installer to make changes in the alignment of the pavers.

Buildings and concrete curbing are normally not straight and must not be utilized for establishing straight joint lines. The use of string lines is vital to figure out the real straightness of the edge. As the paver installation progresses, the string lines will help reduce the need for small trim pieces.

These will preserve a minimum joint width and permit the bed linen and jointing sand to get in between each paver. Pavers with spacer bars are generally not laid in snug against each other because a string line will offer consistent joint spacing.

Installation of brick pavers.

One of the most commonly utilized techniques for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have actually pulled or above the bedding sand. The best method is to position a paver versus another one and let it move down into the bed linen sand.

When setting up pavers on a high grade, they must be set up at the base of the grade going uphill. This will prevent the pavers from creeping as they are being laid.

On large business and commercial applications, hand laying pavers would not be cost effective due to the labor strength. The very best method for installing pavers on large projects is to install them mechanically. The use of a mechanical laying machine can set up around 6000 - 7000 sq ft a day. There are a couple products a specialist ought to consider before setting up pavers mechanically:

1.) Mechanical installers are just efficient in installing pavers in certain patterns.

2.) The professional needs to make certain that the producer is capable of manufacturing and bundling pavers in the desired pattern on the pallets for simple mechanical installation.

3.) Specialists might experience a color blending situation coming off the packages of pavers Poor color mixing might result in a patchy looking installation. Most makers follow color blending on each bundle of pavers, but it is the specialist's obligation to guarantee proper blending in the field.

Cutting procedures for brick pavers.

Specialists generally have two methods of cutting pavers. When cutting pavers wet, it will help lessen dust and will extend the diamond blades life. The operator of the brick saw should constantly cut the pavers away from the surface of the paver field when cutting damp, due to the fact that the pavers will develop a slurry that will stain the paver surface.

The brick saw operator ought to always wear the correct security that is needed for running a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a major function in the overall success of an interlocking pavement installation Edging restraints remove lateral motion of the pavers and hold the pavers tightly together. Specifically at the outer perimeter of the paver application, without an edging restraint, your job is guaranteed to stop working over time.

Typically made edge restraints are the most commonly utilized by contractors. Made edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone.

Edging installation.

When installing your edge restraint, it ought to rest straight on top of the compacted gravel base. The compressed gravel base course ought to extend a minimum of 6in beyond the border of the pavers This will provide a proper structure upon which the edging restraint can sit. Produced edging (i.E. Plastic, steel or aluminum) should be securely anchored into the compacted gravel base( contact the producer's literature for the advised spacing of the spikes). There are some edging restraints that will extend deeper into the gravel base or beyond the base course (i.E. Timbers or poured-in-place curbs ). Edging restraints must never be put straight on top of the bedding sand. This might result in the migration of the bed linen sand and ultimate lateral movement of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile material is suggested. When a gap in between the pavers and the edging goes beyond 3/8" (10mm), then the space must be filled with cut pavers. All edging applications should be appropriately back filled after they are set up to help offer extra stability.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The whole location that is to be compacted ought to be swept tidy of any foreign things and debris that can trigger scratching or scuffing on the surface of the pavers.

In addition, it is essential that the very first compaction takes place before any jointing sand has been used to the pavers. If jointing sand is used to the pavers prior to compaction takes place, this can cause a bridging issue and will not permit the joints to be entirely filled with jointing sand. This can also prevent the pavers from being appropriately set into the bed linen sand.

When condensing the pavers, it is recommended that you make a minimum of 2 passes in various directions across the pavers. This will enable the pavers to be appropriately embeded in the bed linen sand and will force the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is extremely vital to the last efficiency of the pavers. Failure to do correct compaction can result in deformations and pavement failure in time.


Paver pallets/bundles must be positioned in a way not to interfere with the paver installation. One of the most widely used methods for the installation of pavers is hand installation of each paver. The operator of the brick saw ought to constantly cut the pavers away from the surface of the paver field when cutting wet, due to the reality that the pavers will create a slurry that will stain the paver surface. Edging restraints get rid of lateral movement of the pavers and hold the pavers firmly together. When a space Koi Pond Florida in between the pavers and the edging goes beyond 3/8" (10mm), then the area should be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *